1. The Forum Rules have undergone some minor changes and updates.  Please take the time to read them; it will only take a couple of minutes of your time. By doing so, you lessen the chance of incurring the wrath of the moderation team or making yourself look foolish to other members.

    90% of users posting adverts in the Sales forums need to be reminded to read the rules as their posts are wrong.  This is unnecessarily time-consuming and will no longer happen - if your advert doesn't follow the Sales Rules it will be deleted and you'll have to start all over again.

    To close this box once you've read it (and the Rules), click on the X in the top right-hand corner.

    Thank you.

    AGF Staff



    Dismiss Notice
  2. Hotmail block emails from us entering your inbox. Unless you can setup a safe sender you will not get activation emails from the forum. Please use an alternative provider or complain to Hotmail.
    Hotmail addresses include.

    @Hotmail.co.uk @Hotmail.com @outlook.com @Live.com
    Dismiss Notice

Question Rusty Co2 Bulb

Discussion in 'Anything Airgun Related' started by VIKING6661, May 16, 2018.

  1. VIKING6661

    VIKING6661 Post Whore

    Messages:
    1,171
    Likes Received:
    623
    Location:
    Chigwell Essex
    So just checking but I’m guessing this one is not to be used ? If so what’s the correct way to dispose of it ?

    [​IMG]


    Sent from my iPhone using Tapatalk
     
  2. cloverleaf

    cloverleaf Super Moderator Staff Member Mod/Admin

    Messages:
    13,594
    Likes Received:
    2,947
    Location:
    Oxfordshire
    I don't see why it should present a problem; just make sure that the flaky finish isn't going to get it jammed inside the gun (2240 etc) and that the corrosion won't contact / mark the little screw platform ("piercing plate") on other guns.
     
    foxtrott likes this.
  3. Nobbi1977

    Nobbi1977 Donator

    Messages:
    538
    Likes Received:
    263
    Location:
    Lincolnshire
    The pressure is already in it so if it was going to fail it would have done. If it fits ok the plink it off and then bin it
     
    VIKING6661 likes this.
  4. gunsnlandies

    gunsnlandies Busy Member

    Messages:
    681
    Likes Received:
    157
    Location:
    stowmarket
    If you still have your 78, use it in that. The 2240 takes gas one shot at a time from the capsule. The 78 empties into the chamber in one hit. So no problem.
     
    VIKING6661 likes this.
  5. mikeyhall1

    mikeyhall1 Top Poster

    Messages:
    12,604
    Likes Received:
    8,394
    Location:
    Chelmsford/Upminster - Essex
    I'd still use it mate
     
    VIKING6661 and foxtrott like this.
  6. Tiger36

    Tiger36 Well-Known Member

    Messages:
    75
    Likes Received:
    75
    Location:
    Copthorne
    Pretty sure the seal on the end would be the weakest link at would give way 1st??
     
    VIKING6661 likes this.
  7. VIKING6661

    VIKING6661 Post Whore

    Messages:
    1,171
    Likes Received:
    623
    Location:
    Chigwell Essex
    Thanks guys just wanted to make sure just in case it went bang in a pistol


    Sent from my iPhone using Tapatalk
     
  8. littleJon365

    littleJon365 Post Whore

    Messages:
    1,284
    Likes Received:
    897
    Location:
    Harlow, Essex
    I’d use it, you won’t have an issue.
     
    VIKING6661 likes this.
  9. littleJon365

    littleJon365 Post Whore

    Messages:
    1,284
    Likes Received:
    897
    Location:
    Harlow, Essex
    I’m assuming it didnt come like that
     
  10. VIKING6661

    VIKING6661 Post Whore

    Messages:
    1,171
    Likes Received:
    623
    Location:
    Chigwell Essex
    I can’t remember keep a lot of Co2 as it’s cheeper to bulk but then packs of 10 go about 70 bulbs between two brands at the moment and it’s the only one like it


    Sent from my iPhone using Tapatalk
     
    littleJon365 likes this.
  11. That hurts

    That hurts Barely Active

    Messages:
    5,716
    Likes Received:
    2,235
    Location:
    Diss
    Clean all the loose cr@p off it first and then use
     

Share This Page